EC-M11-EG-C5-LTE – USER GUIDE

Programming  #

The NORVI EC-M11-EG-C5-LTE has a mini USB port for serial connection with the SoC for programming. Any ESP32-supported programming IDE can be used to program the controller. Follow this guide to programming NORVI ESP32-based Based Controllers with Arduino IDE.

SoC: ESP32-WROOM32
Programming Port: USB UART

8-pin Connector and wire harness #

Pin Description #

I2C Communication #

Programming I2C Communication #

#include <Wire.h>
// Define the I2C device address
#define DEVICE_ADDRESS 0x49

void setup() {
  Wire.begin(16, 17);  // SDA on GPIO16, SCL on GPIO17
  Serial.begin(115200);
}

void loop() {
  // Write data to the I2C device
  Wire.beginTransmission(DEVICE_ADDRESS);
  Wire.write(0x01);  // Replace with your data
  Wire.write(0x02);
  Wire.write(0x03);
  Wire.endTransmission();
  delay(100);
  // Read data from the I2C device
  Wire.requestFrom(DEVICE_ADDRESS, 3);  // 3 bytes of data
  if (Wire.available() >= 3) {
    byte data1 = Wire.read();
    byte data2 = Wire.read();
    byte data3 = Wire.read();
    Serial.print("Read Data: ");
    Serial.print(data1, HEX);
    Serial.print(" ");
    Serial.print(data2, HEX);
    Serial.print(" ");
    Serial.println(data3, HEX);
  }
  delay(1000);  // Delay for demonstration purposes
}

LTE1 Communication #

LTE2 Communication #

Programming LTE Communication #

#define MODEM_RESET 32
#define MODEM_FLIGHT 22
#define MODEM_RX 26
#define MODEM_TX 25
long timer1;
void setup() {           // initialize both serial ports:
  Serial.begin(115200);
  pinMode(MODEM_FLIGHT , OUTPUT);       // FLIGHT MODE ENABLE
  pinMode(MODEM_RESET , OUTPUT);       // MODEM RESET PIN
  digitalWrite(MODEM_FLIGHT, HIGH);   // FLIGHT MODE 
  MODEM_RESET_CYC();
  delay(2000);
  Serial2.begin(115200, SERIAL_8N1, MODEM_RX, MODEM_TX);
  Serial.println("SIM AT ATART >>>>>>>>>>>>>>");
  delay(2000);
  Serial2.println("AT");
  delay(2000);
  Serial2.println("AT+CPIN?");
  delay(2000);
  Serial2.println("AT+CNMP?");
}
void loop() {
  delay(3000);
  timer1 = millis();
  Serial2.println("AT");
  while(millis()<timer1+10000){
    while (Serial2.available()) {
    int inByte = Serial2.read();
    Serial.write(inByte);
    }
  }
  timer1 = millis();
  Serial2.println("AT+CPIN?");
  while(millis()<timer1+10000){
    while (Serial2.available()) {
    int inByte = Serial2.read();
    Serial.write(inByte);
    }
  }
  Serial.println("AT SCAN DONE");         // read from port 0, send to port 1:
  while (Serial.available()) {
    int inByte = Serial.read();
    Serial2.write(inByte);
  }
  while (Serial2.available()) {
    int inByte = Serial2.read();
    Serial.write(inByte);
  }
}
void MODEM_RESET_CYC() {
  digitalWrite(MODEM_RESET,HIGH );
  delay(1000);
  digitalWrite(MODEM_RESET,LOW );
  delay(1000);
  digitalWrite(MODEM_RESET, HIGH);
}