---
title: "EC-M11-EG-C3-S – USER GUIDE"
description: "## Programming  The NORVI EC-M11-EG-C3-S has a mini USB port for serial connection with the SoC for programming. Any ESP32-supported programming IDE can be used to program the controller. Follow this Guide to programming NORVI ESP32 controllers with the Arduino…"
url: "https://norvi.io/docs/norvi-ec-m11-eg-c3-s-user-guide/"
updated: "2026-03-20"
category: "OTHER PRODUCTS / EC-M11-EG LoRa / EC-M11-EG-C3-S"
---

# EC-M11-EG-C3-S – USER GUIDE

## Programming 

The NORVI EC-M11-EG-C3-S has a mini USB port for serial connection with the SoC for programming. Any ESP32-supported programming IDE can be used to program the controller. Follow this Guide to programming NORVI ESP32 controllers with the Arduino IDE.

**SoC:** ESP32-WROOM32
**Programming Port:**USB UART

## 8-pin Connector and wire harness

![](https://norvi.io/wp-content/uploads/2024/09/345-4.jpg)

### Pin Description

| 8P Male | Wire color | I/O Configuration |
| --- | --- | --- |
| 1 | White | A+ |
| 2 | Brown | A- |
| 3 | Green | B+ |
| 4 | Yellow | B- |
| 5 | Gray | RS-485A |
| 6 | Pink | RS-485B |
| 7 | Blue | Power+ |
| 8 | Red | Power- |

## Load Cell Inputs

### Programming Load Cell Inputs

| Number of Load Cell Inputs | 1 |
| --- | --- |
| Module Type | HX711 |
| PD SCK | GPIO32 |
| DOUT | GPIO33 |

```cpp

                #include "HX711.h"
const int LOADCELL_DOUT_PIN = 33;
const int LOADCELL_SCK_PIN = 32;
HX711 scale;

void setup() {
  Serial.begin(115200);
  Serial.println("HX711 Demo");
  Serial.println("Initializing the scale");
  scale.begin(LOADCELL_DOUT_PIN, LOADCELL_SCK_PIN);
  scale.set_scale(2280.f);
  // this value is obtained by calibrating the scale with known weights;
  //see the README for details
  scale.tare();                // reset the scale to 0
  Serial.println("After setting up the scale:");
  Serial.print("read: tt");
  Serial.println(scale.read());               // print a raw reading from the ADC
  Serial.print("read average: tt");
  Serial.println(scale.read_average(20));
  // print the average of 20 readings from the ADC
  Serial.print("get value: tt");
  Serial.println(scale.get_value(5));
  // print the average of 5 readings from the ADC minus the tare weight,
  //set with tare()
  Serial.print("get units: tt");
  Serial.println(scale.get_units(5), 1);
  // print the average of 5 readings from the ADC minus tare weight, divided
  Serial.println("Readings:");
}

void loop() {
  Serial.print("one reading:t");
  Serial.print(scale.get_units(), 1);
  Serial.print("t| average:t");
  Serial.println(scale.get_units(10), 1);
}
```

## RS-485 Communication

| Driver | MAX485 |
| --- | --- |
| UART RX | GPIO4 |
| UART TX | GPIO2 |
| Flow Control | GPIO13 |

GPIO Connections of RS-485

### Programming RS-485

NORVI EC-M11-EG series RS-485 connection uses a half-duplex mode of MAX485 transmitter with UART
Communication.

```cpp

                #define RS485_FC 13
void setup() {
   Serial.begin(115200);
   Serial.println("Device Starting");
   pinMode(RS485_FC, OUTPUT);
}
void loop() {
  digitalWrite(RS485_FC, HIGH); // Turns on Transmitter Mode
  Serial.println("RS-485 Sending");
  delay(500);
}
```

## LoRa Transceiver Module

| Specification | Long Range(LoRa) |
| --- | --- |
| RF Transceiver | Order depending on regional regulations |
| SPI MISO | GPIO19 |
| SPI MOSI | GPIO23 |
| SPI SCK | GPIO18 |
| NSS | GPIO26 |
| DIO0 | GPIO25 |
| DIO1 | GPIO27 |
| DIO2 | NOT CONNECTED |
| RESET | GPIO15 |

### Programming LoRa Modules

```cpp

                #include <lmic.h>
#include <hal/hal.h>
#include <SPI.h>
#define CONFIRMED_MSG_RETRY_COUNT 3
static const u1_t PROGMEM APPEUI[8] = { 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00 };

void os_getArtEui (u1_t* buf) {
  memcpy_P(buf, APPEUI, 8);
}

static const u1_t PROGMEM DEVEUI[8] = {0x4B, 0x11, 0x3F, 0xB1, 0x3C, 0xBE, 0xD6, 0x56};
void os_getDevEui (u1_t* buf) {
  memcpy_P(buf, DEVEUI, 8);
}

static const u1_t PROGMEM APPKEY[16] = {0xF9, 0x65, 0xE4, 0xED, 0xFF, 0x8A, 0x89, 0x27, 0x23, 0xA6, 0xB7, 0x42, 0x2F, 0x05, 0x8E, 0x9F};
void os_getDevKey (u1_t* buf) {
  memcpy_P(buf, APPKEY, 16);
}

static uint8_t mydata[] = "Hello, world!";
static osjob_t sendjob;
const unsigned TX_INTERVAL = 60;
const lmic_pinmap lmic_pins = {
  .nss = 26,
  .rxtx = LMIC_UNUSED_PIN,
  .rst = 15,
  .dio = {25, 27, -1},
};

void printHex2(unsigned v) {
  v &= 0xff;
  if (v < 16)
    Serial.print('0');
  Serial.print(v, HEX);
}
```
