---
title: "EC-M11-EG-C3-B95 – USER GUIDE"
description: "## Programming  The NORVI EC-M11-EG-C3-B95 has a mini USB port for serial connection with the SoC for programming. Any ESP32-supported programming IDE can be used to program the controller. Follow this Guide to programming NORVI ESP32 controllers with the Arduino…"
url: "https://norvi.io/docs/norvi-ec-m11-eg-c3-b95-user-guide/"
updated: "2026-03-24"
category: "OTHER PRODUCTS / EC-M11-EG NB-IoT / EC-M11-EG-C3-B95"
---

# EC-M11-EG-C3-B95 – USER GUIDE

## Programming 

The NORVI EC-M11-EG-C3-B95 has a mini USB port for serial connection with the SoC for programming. Any ESP32-supported programming IDE can be used to program the controller. Follow this Guide to programming NORVI ESP32 controllers with the Arduino IDE.

SoC: ESP32-WROOM32
Programming Port: USB UART

## 8-pin Connector and wire harness

![](https://norvi.io/wp-content/uploads/2024/09/345-33.jpg)

### Pin Description

| 8P Male | Wire color | I/O Configuration |
| --- | --- | --- |
| 1 | White | A+ |
| 2 | Brown | A- |
| 3 | Green | B+ |
| 4 | Yellow | B- |
| 5 | Gray | RS-485A |
| 6 | Pink | RS-485B |
| 7 | Blue | Power+ |
| 8 | Red | Power- |

## Load Cell Inputs

### Programming Load Cell Inputs

| Number of Load Cell Inputs | 1 |
| --- | --- |
| Module Type | HX711 |
| PD SCK | GPIO32 |
| DOUT | GPIO33 |

```cpp

                #include "HX711.h"
const int LOADCELL_DOUT_PIN = 33;
const int LOADCELL_SCK_PIN = 32;
HX711 scale;

void setup() {
  Serial.begin(115200);
  Serial.println("HX711 Demo");
  Serial.println("Initializing the scale");
  scale.begin(LOADCELL_DOUT_PIN, LOADCELL_SCK_PIN);
  scale.set_scale(2280.f);
  // this value is obtained by calibrating the scale with known weights;
  //see the README for details
  scale.tare();                // reset the scale to 0
  Serial.println("After setting up the scale:");
  Serial.print("read: tt");
  Serial.println(scale.read());
  // print a raw reading from the ADC
  Serial.print("read average: tt");
  Serial.println(scale.read_average(20));
  // print the average of 20 readings from the ADC
  Serial.print("get value: tt");
  Serial.println(scale.get_value(5));
  // print the average of 5 readings from the ADC minus the tare weight,
  //set with tare()
  Serial.print("get units: tt");
  Serial.println(scale.get_units(5), 1);
  // print the average of 5 readings from the ADC minus tare weight, divided
  Serial.println("Readings:");
}

void loop() {
  Serial.print("one reading:t");
  Serial.print(scale.get_units(), 1);
  Serial.print("t| average:t");
  Serial.println(scale.get_units(10), 1);
}
```

## **RS-485 Communication**

| Driver | MAX485 |
| --- | --- |
| UART RX | GPIO4 |
| UART TX | GPIO2 |
| Flow Control | GPIO13 |

GPIO Connections of RS-485

### **Programming RS-485**

NORVI EC-M11-EG series RS-485 connection uses a half-duplex mode of MAX485 transmitter with UART
Communication.

```cpp

                #define RS485_FC 13
void setup() {
   Serial.begin(115200);
   Serial.println("Device Starting");
   pinMode(RS485_FC, OUTPUT);
}
void loop() {
  digitalWrite(RS485_FC, HIGH); // Turns on Transmitter Mode
  Serial.println("RS-485 Sending");
  delay(500);
}
```

## **NB-IoT Module**

| Modem | NB-101 |
| --- | --- |
| RX | GPIO25 |
| TX |  GPIO26 |
| POWER | GPIO22 |
| RESET | GPIO17 |

### **Programming NB-IoT**

```cpp

                const int GSM_RST = 17;        // Define the pin for modem reset
const int GSM_PWR_KEY = 22;    // Define the pin for modem power key
const int MODEM_RX = 25;      // Define the pin for ESP32's RX to modem's TX
const int MODEM_TX = 26;      // Define the pin for ESP32's TX to modem's RX

void setup() {
  pinMode(GSM_RST, OUTPUT);
  pinMode(GSM_PWR_KEY, OUTPUT);
  digitalWrite(GSM_PWR_KEY, HIGH);  // Set modem to flight mode
  digitalWrite(GSM_RST, HIGH);
  delay(1000);
  digitalWrite(GSM_RST, LOW);
  delay(1000);
  digitalWrite(GSM_RST, HIGH);
  delay(1000);
  Serial.begin(9600);  // Initialize the serial monitor
  Serial2.begin(9600, SERIAL_8N1, MODEM_RX, MODEM_TX);
  // Initialize communication with modem
  Serial.println("SIM AT START >>>>>>>>>>>>>>");
  delay(2000);
  Serial.flush();
  Serial2.println("AT+NCONFIG=AUTOCONNECT,TRUE");
  delay(2000);
  while (Serial2.available()) {
    char response = Serial2.read();
    Serial.write(response);
  }
  Serial2.println("AT");
  delay(2000);
  while (Serial2.available()) {
    char response = Serial2.read();
    Serial.write(response);
  }
  Serial2.println("AT+CEREG?");
  delay(2000);
  while (Serial2.available()) {
    char response = Serial2.read();
    Serial.write(response);
  }
  Serial.flush();
}

void loop() {
  Serial.print(".");
  Serial2.println("AT");
  while (Serial2.available()) {
    char response = Serial2.read();
    Serial.write(response);
  }
  delay(5000);
  Serial2.println("AT+CEREG?");
  delay(2000);
  while (Serial2.available()) {
    char response = Serial2.read();
    Serial.write(response);
  }
}
```
