---
title: "EC-M11-BC-C3-B95 – USER GUIDE"
description: "## Programming  The NORVI EC-M11-BC-C3-B95 has a mini USB port for serial connection with the SoC for programming. Any ESP32-supported programming IDE can be used to program the controller. Follow this guide to programming NORVI ESP32-based controllers with the Arduino…"
url: "https://norvi.io/docs/norvi-ec-m11-bc-c3-b95-user-guide/"
updated: "2026-03-19"
category: "OTHER PRODUCTS / EC-M11-BC NB-IoT / EC-M11-BC-C3-B95"
---

# EC-M11-BC-C3-B95 – USER GUIDE

## Programming 

The NORVI EC-M11-BC-C3-B95 has a mini USB port for serial connection with the SoC for programming. Any ESP32-supported programming IDE can be used to program the controller. Follow this guide to programming NORVI ESP32-based controllers with the Arduino IDE.

**SoC:** ESP32-WROOM32
**Programming Port:**USB UART

## Wiring Load Cell Input and Solar.

### 8-pin and 3-pin connectors and wire harness

![](https://norvi.io/wp-content/uploads/2024/09/df-1024x348-17.jpg)

### Pin Description

| **8P Male** | **Wire color** | **I/O Configuration** |
| --- | --- | --- |
| 1 | White | A+ |
| 2 | Brown | A- |
| 3 | Green | B+ |
| 4 | Yellow | B- |
| 5 | Gray | - |
| 6 | Pink | - |
| 7 | Blue | - |
| 8 | Red | - |

| **3P Male** | **Wire color** | **I/O Configuration** |
| --- | --- | --- |
| 1 | Blue | Solar Panel + |
| 2 | Black | Not in Use |
| 3 | Brown | Solar Panel - |

## Load Cell Inputs

### Programming Load Cell Inputs 

| Number of Load Cell Inputs | 1 |
| --- | --- |
| Module Type | HX711 |
| PD SCK | GPIO12 |
| DOUT | GPIO13 |

```cpp

                #include "HX711.h"
const int LOADCELL_DOUT_PIN = 13;
const int LOADCELL_SCK_PIN = 12;
HX711 scale;

void setup() {
  Serial.begin(115200);
  Serial.println("HX711 Demo");
  Serial.println("Initializing the scale");
  scale.begin(LOADCELL_DOUT_PIN, LOADCELL_SCK_PIN);
  scale.set_scale(2280.f);
  // this value is obtained by calibrating the scale with known weights;
  //see the README for details
  scale.tare();                // reset the scale to 0
  Serial.println("After setting up the scale:");
  Serial.print("read: tt");
  Serial.println(scale.read());
  // print a raw reading from the ADC
  Serial.print("read average: tt");
  Serial.println(scale.read_average(20));
  // print the average of 20 readings from the ADC
  Serial.print("get value: tt");
  Serial.println(scale.get_value(5));
  // print the average of 5 readings from the ADC minus the tare weight,
  //set with tare()
  Serial.print("get units: tt");
  Serial.println(scale.get_units(5), 1);
  // print the average of 5 readings from the ADC minus tare weight, divided
  Serial.println("Readings:");
}
void loop() {
  Serial.print("one reading:t");
  Serial.print(scale.get_units(), 1);
  Serial.print("t| average:t");
  Serial.println(scale.get_units(10), 1);
}
```

## **NB-IoT Module**

| Modem | NB-101 |
| --- | --- |
| RX | GPIO25 |
| TX |  GPIO26 |
| POWER | GPIO32 |
| RESET | GPIO27 |

### **Programming NB-IoT**

```cpp

                const int GSM_RST = 17;        // Define the pin for modem reset
const int GSM_PWR_KEY = 22;    // Define the pin for modem power key
const int MODEM_RX = 25;      // Define the pin for ESP32's RX to modem's TX
const int MODEM_TX = 26;      // Define the pin for ESP32's TX to modem's RX

void setup() {
  pinMode(GSM_RST, OUTPUT);
  pinMode(GSM_PWR_KEY, OUTPUT);
  digitalWrite(GSM_PWR_KEY, HIGH);  // Set modem to flight mode
  digitalWrite(GSM_RST, HIGH);
  delay(1000);
  digitalWrite(GSM_RST, LOW);
  delay(1000);
  digitalWrite(GSM_RST, HIGH);
  delay(1000);
  Serial.begin(9600);  // Initialize the serial monitor
  Serial2.begin(9600, SERIAL_8N1, MODEM_RX, MODEM_TX);
  // Initialize communication with modem
  Serial.println("SIM AT START >>>>>>>>>>>>>>");
  delay(2000);
  Serial.flush();
  Serial2.println("AT+NCONFIG=AUTOCONNECT,TRUE");
  delay(2000);
  while (Serial2.available()) {
    char response = Serial2.read();
    Serial.write(response);
  }
  Serial2.println("AT");
  delay(2000);
  while (Serial2.available()) {
    char response = Serial2.read();
    Serial.write(response);
  }
  Serial2.println("AT+CEREG?");
  delay(2000);
  while (Serial2.available()) {
    char response = Serial2.read();
    Serial.write(response);
  }
  Serial.flush();
}

void loop() {
  Serial.print(".");
  Serial2.println("AT");
  while (Serial2.available()) {
    char response = Serial2.read();
    Serial.write(response);
  }
  delay(5000);
  Serial2.println("AT+CEREG?");
  delay(2000);
  while (Serial2.available()) {
    char response = Serial2.read();
    Serial.write(response);
  }
}
```

## **Solar Input**

| Solar Powered Model | CN3083  |
| --- | --- |
| Maximum Charge Current |  600mA  |
| Maximum Voltage |  6V  |
| Input Voltage monitor |  ADS1115 - 0x49 - AIN2 |

## **Battery Input**

| Battery Type | 103040 Lithium polymer battery |
| --- | --- |
| Nominal Capacity  | 1200mAh   |
| Nominal Voltage | 3.75V |
| Overcharge | 4.2V |
| Over-discharge Cutoff Voltage | 3V |

### **Programming Solar and Battery**

```cpp

                #include <Adafruit_SSD1306.h>
#include <Adafruit_ADS1X15.h>
Adafruit_ADS1115 ads1;
int analog_value = 0;
void setup() {
  Serial.begin(115200);// put your setup code here, to run once:
  Wire.begin(16,17);
  if (!ads1.begin(0x49)) {
    Serial.println("Failed to initialize ADS 1 .");
    while (1);
  }
}
void loop() {
  int16_t adc0, adc1, adc2, adc3;
  adc0 = ads1.readADC_SingleEnded(0);
  adc1 = ads1.readADC_SingleEnded(1);
  adc2 = ads1.readADC_SingleEnded(2);
  adc3 = ads1.readADC_SingleEnded(3);
  Serial.println("-----------------------------------------------------------");
  Serial.print("AIN1: "); Serial.print(adc0); Serial.println("  ");
  Serial.print("AIN2: "); Serial.print(adc1); Serial.println("  ");
  Serial.print("SOLAR: "); Serial.print(adc2); Serial.println("  ");
  Serial.print("AIN4: "); Serial.print(adc3); Serial.println("  ");
}
```